PRODUCT CODE: WJ0Y8 0WJ0Y8
MPN: WJ0Y8 0WJ0Y8
WJ0Y8 For Dell Pro 14 Plus PB14250 PB14250S 14" FHD+ Touch Screen Assembly w/ 4G WWAN + IR Camera Silver 0WJ0Y8
QTY on hand: 10
Lead Time: Ships in 7 business days.
$ 260
$ 270
SKU
10
category:
Key words:
隐藏域元素占位
- DESCRIPTION
-
- Brand: DELL
- Commodity name: WJ0Y8 For Dell Pro 14 Plus PB14250 PB14250S 14" FHD+ Touch Screen Assembly w/ 4G WWAN + IR Camera Silver 0WJ0Y8
- Commodity ID: WJ0Y8 0WJ0Y8
- MPN: WJ0Y8 0WJ0Y8
WJ0Y8 For Dell Pro 14 Plus PB14250 PB14250S 14" FHD+ Touch Screen Assembly w/ 4G WWAN + IR Camera Silver 0WJ0Y8
【Product Overview】
This is a complete 14.0-inch FHD+ (WUXGA) IPS touchscreen display assembly for the Dell Pro 14 Plus PB14250 and PB14250S laptop series, finished in Silver. The assembly is supplied as a hinge-up top lid and is built for configurations fitted with a 4G/LTE WWAN module and an IR camera for Windows Hello facial recognition — the WWAN antenna pair and IR camera module are already integrated into the lid, so no separate antenna kit or camera swap is required.
The 1920×1200 resolution on a 16:10 aspect ratio provides noticeably more vertical workspace than a 16:9 FHD panel of the same diagonal, which is why this assembly will not interchange with standard 1920×1080 14-inch lids — the panel height, hinge geometry, and bezel opening are all different.
【Product Specifications】
【Key Highlights】
- 16:10 FHD+ workspace — 1920×1200 delivers 11% more vertical viewing height than 1920×1080, ideal for spreadsheets, code, and document work
- Full touch with IPS anti-glare — factory-bonded digitizer with matte anti-glare surface; reduces fingerprints and outdoor reflections without the glare of a glossy panel
- 4G WWAN ready — antenna pair pre-routed in the lid, so field units keep LTE connectivity after the swap; no antenna re-routing or foil re-taping
- IR camera for Windows Hello — facial recognition login stays functional; the module ships installed, avoiding the most common post-repair failure point
- Complete hinge-up assembly — panel, digitizer, bezel, camera, and antenna cables arrive pre-assembled; reduces repair time to a single disassembly sequence
- Silver finish match — colour-matched to the PB14250 chassis for a factory-consistent appearance on resale and fleet deployments
【Package Includes】
- 1 × Complete 14.0" FHD+ 1920×1200 IPS Touchscreen Assembly (Silver)
- 1 × Pre-installed IR Camera Module
- 1 × Pre-routed 4G WWAN / WLAN Antenna Cable Set
- 1 × Front Bezel (factory fitted)
- Protective ESD bag and rigid foam packaging
Note: Screws, hinge brackets, and the bottom chassis are not included unless stated in the listing variant.
【Installation Guide and Precautions】
- Disable the built-in battery first. Enter BIOS (F2 at boot) →
Battery Configuration→ set Disable Built-in Battery → save and exit. The system powers down. This prevents short circuits while the display cable is disconnected. - Full ESD protection is mandatory. Use a wrist strap and grounded mat. The touch digitizer and IR camera ribbon are static-sensitive and are not covered under warranty if damaged during handling.
- Handle the panel by the edges only. Do not press the centre of the glass or the back of the panel — pressure on the bonded digitizer creates permanent mura (pressure marks) that appear as blotches on a white background.
- Route the WWAN antenna cables exactly as removed. Photograph the original cable path before disassembly. The 4G antenna pair must sit in its designated channel in the lid; a mis-routed cable will cause weak signal or dropped LTE connections that are difficult to diagnose later.
- Seat the eDP connector fully and latch it. Insert the display cable straight and perpendicular, then close the locking bar. A partially seated connector causes no-backlight, flickering, or single-colour wash — the three most common "dead panel" returns.
- Reconnect the camera/microphone ribbon before closing the bezel. The IR camera cable is short and easily pinched by the hinge cover; test Windows Hello before final assembly.
- Test before final torque. Power on with the assembly loosely fitted. Verify touch calibration across all four corners, camera recognition, and WWAN signal. Only then torque the hinges and seat the bezel clips.
⚠️ Compatibility warnings — please read before ordering:
- This is the touch + 4G WWAN + IR variant. It is not interchangeable with the non-touch 400-nit FHD+ assembly (0D0NR9), which uses a different panel stack and bezel.
- Not compatible with the PB14255 2-in-1 convertible — that model uses a 360° hinge and a different lid structure.
- Fitting this lid to a WLAN-only chassis is mechanically possible but the WWAN antennas will be unused; confirm the unit has a WWAN card slot and SIM tray before ordering.
- This is a 1920×1200 (16:10) assembly. It will not fit 1920×1080 (16:9) 14-inch Dell models.
Related Products